Achronix ACE Version 5.0 Manuel d'utilisateur Page 91
- Page / 389
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Editors Chapter 3. Concepts
Enable L1 ASPM
Support
Active State Power Management (ASPM) Support
L1 Entry Time (hex)
Number of microseconds of idle time to wait before requesting entry to ASPM
L1 (used by Upstream Ports Endpoint/Upstream Switch - only). Idle time is
defined as no TLP or ACK/NAK DLLP transmissions. PCIe Specification does
not define a minimum or maximum value. Too low a value risks wasting link
bandwidth due to ASPM L1 entry/exit latencies. Too high a value will reduce
ASPM L1 power savings. Only used if Enable L1s Power Mgmt is set. 0 is a
special case and selects 1000 uS (0x3e8)
Endpoint L1
Acceptable Latency
From PCI Express Base Specification, Rev 2.1 section 7.8.3: This field indicates
the acceptable latency that an Endpoint can withstand due to the transition
from L1 state to the L0 state. It is essentially an indirect measure of the
Endpoint’s internal buffering
L1 Exit Latency
Length of time required to complete transition from L1 to L0
79 http://www.achronix.com UG001 Rev. 5.0 - 5th December 2012
- ACE User Guide 1
- Copyright Info 2
- Contents 3
- About This Guide 13
- Related Documents 13
- Getting Started 14
- ACE Quickstart Tutorial 15
- Concepts 16
- Text Editor 18
- HTML Report Browser 19
- Basic PLL Configuration Editor 32
- BRAM Configuration Editor 35
- DDR3 Configuration Editor 40
- Ethernet Configuration Editor 51
- FIFO Configuration Editor 55
- Interrupt Settings Page 72
- LRAM Configuration Editor 78
- LRAM FIFO Configuration Editor 81
- Memory Map Page 88
- ROM Configuration Editor 97
- SerDes Configuration Editor 100
- Editors Chapter 3. Concepts 102
- Channel Bonding Page 118
- VCD Waveform Editor 126
- Fast views 129
- Projects View 130
- Flow View 132
- Options View 134
- Multiprocess View 141
- Tcl Console View 147
- Search View 148
- Selection View 152
- Views Chapter 3. Concepts 155
- Figure 3.74: Selection View 155
- Critical Paths View 156
- Critical Path Diagram View 160
- Package View 164
- IO Assignment View 168
- Clock Regions View 172
- Netlist Browser View 174
- Placement Regions View 177
- Outline View 180
- IP Libraries View 181
- IP Diagram View 182
- IP Problems View 184
- Download View 186
- ”net192.168.100.101” 187
- Create Project Dialog 188
- Load Project Dialog 189
- Create Implementation Dialog 190
- Restore Implementation Dialog 191
- Save Implementation Dialog 192
- Create a New Text File Dialog 194
- Add Source Files Dialog 195
- Save Placement Dialog 197
- Save Script File Dialog 199
- New IP Configuration Dialog 200
- Configure Selected IOs Dialog 203
- Configure Table Columns Dialog 207
- Search Filter Builder Dialog 211
- Save Placement Regions Dialog 215
- Toolbars 216
- Preferences 217
- Floorplanner view 220
- IP Diagram Preference Page 225
- Package View Preference Page 230
- Text Editors Preference Page 234
- Projects 237
- Project File 239
- Source Files 239
- IP Configurations 239
- Output Files 240
- Log Files 240
- Flow Steps 242
- Flow Status 242
- Clock Report 243
- Utilization Report 243
- Pin Assignment Report 243
- Timing Report 244
- I/O Timing Report 245
- Routing Report 245
- Power Dissipation Report 245
- Multiprocess Summary Report 245
- Advanced Concepts 247
- Running ACE 248
- Working With Perspectives 249
- Opening Views 250
- Moving and Docking Views 250
- Rearranging Tabbed Views 250
- Creating Fast Views 251
- Tiling Editors 251
- Maximizing a View or Editor 251
- Creating Projects 252
- Loading Projects 252
- Removing Projects 252
- Saving Projects 252
- Adding Source Files 254
- Removing Source Files 255
- Creating Implementations 255
- Saving Implementations 256
- Restoring Implementations 256
- Copying Implementations 257
- Removing Implementations 257
- Running the Flow 259
- Place and Route Steps 260
- Design Completion Steps 260
- FPGA Programming Steps 261
- 2 5035008 263
- Using the Tcl Console 267
- Command Help 268
- Text Limit 269
- Clearing the Console 269
- Viewing the ACE Log File 270
- Object Type Prefixes 270
- Creating an IP Configuration 271
- Setting the IP Configuration 272
- Viewing the Floorplanner 273
- Selecting Objects 274
- Deselecting Objects 274
- Toggling Mouse Tools 275
- Filtering the View 275
- Getting Object Tooltips 275
- Viewing Object Labels 276
- Viewing the Package Layout 277
- Pre-Placing a Design 281
- Removing Placement 283
- Analyzing Critical Paths 284
- Zooming to Critical Paths 286
- Using Critical Path Diagrams 286
- Intermediate Nodes 290
- Managing I/Os 294
- Running the SnapShot Debugger 295
- Using the SnapShot Macro 297
- VHDL Instantiation: 300
- Setting Up the Scan Chain 302
- Entering a Trigger Pattern 302
- Configuring Test Stimulus 303
- Setting Triggering Range 304
- Configuring the Samples 304
- Collecting Samples 304
- Batch Mode 305
- Playing a STAPL File 306
- Optimizing a Design 307
- Placement Region Preferences 309
- Deleting Placement Regions 313
- Tcl Command Reference 314
- Usage Notes: 349
- Revision History 385
- Version 4.2.0: 387
- Version 3.2.0: 388
Produits connexes et manuels pour Matériel informatique Achronix ACE Version 5.0
(14 pages)© 2020, manymanuals.fr. Tous droits réservés | 1.859 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels